DM368开发 -- 文件烧写_dm368 不能下载 yaffs 程序-程序员宅基地

参看：UG: DaVinci PSP Installation on DM36x EVM

UBL 是 RBL 引导启动的一段小程序，主要负责初始化时钟，串口，NAND，DDR2 等，然后把 uboot, kernel, rootfs 复制到 DDR2 上并引导 uboot。为什么 UBL 跟串口启动一起讲，那是因为这两个关系很密切，很多代码是共用的，而且代码都放在同一个目录下，所以就合起来一起讲了。

一、UBL

ubl 的代码放在 dvsdk 目录下的/psp/flash-utils 文件夹。 flash-utils 目录里有很多基于不同平台的文件夹，但对我 DM36x 来说，只需要 Common 和 DM36x 两个文件夹就可以了，其他的都可以删掉，而且删掉后清爽多了，呵呵。UBL 的源码分析网上已经很多人介绍了，我移植的时候参考了一篇很好的文章：http://zjbintsystem.blog.51cto.com/964211/392000

1. 各个 makefile 的修改

修改各个目录下的 makefile，主要是屏蔽掉不编译的选项。

2. /psp/flash-utils/DM36x/Common/src/devices.c

这个文件很重要，里面包括了所有的 CPU 内部接口的初始化，包括时钟，DDR2，串口......。要是换了 DDR2 那就得在这修改 DDR 的配置。因为这个文件没有定义 CPU 的主频和 DDR2 频率的配置，使用了默认的//Arm 297 DDR 243 MHZ，所以我再这个文件的头部定义了一个宏#define ARM432_DDR340_OSC24

3. /psp/flash-utils/DM36x/Common/src/devices.c

由于 DEVICE_DDR2Init() 函数调用的 DDR_Get_Val() 编译时报错，这个是因为DDR_Get_Val()函数里面的除法和求余函数跟编译器不匹配造成的。改发就是把算好的值代替掉 DDR_Get_Val()。

4./psp/flash-utils/DM36x/GNU/ubl/ubl.lds

这个链接文件里面有内存的起始地址和大小，NAND 的起始地址和大小的配置，这个根据板子的实际情况修改好。
完成上面的修改后就可以 make 了，生成的 ubl_DM36x_nand.bin 就是我们所要的 NAND 启动的 UBL 了。

二。串口启动

串口启动相关的代码在/psp/flash-utils/DM36x/GNU 下面的 sfh,sft,slh,slt。其中 sfh,sft,是一对，sfh(Serial Flasher host)是 PC 端的下载工具，sft(Serial Flasher target)是运行在 ARM 上的程序。编译 sfh 需要 sfl 文件，从 UART 启动时，RBL 先跟 sfh 通讯把 sft 下载到 IRAM 中运行，然后 sft 通过跟 sfh通讯，在 PC 端用命令行的方式把要下载的代码烧写到 NAND 上去。下面是使用的介绍：

Serial Flasher Usage
====================
More info can be found by running the utility with the '-h' option.
sfh_DM36x.exe -h1) Erase the NAND flash
sfh_DM36x.exe -nanderase
2) Flash the NAND with a UBL and u-boot image
sfh_DM36x.exe -nandflash <UBL binary file> <binary application file>
The entry point of the UBL is assumed to be 0x0100, but this can be changed by using the
-UBLStartAddr option. The entry point and load address of the application default to
0x81080000 (u-boot defaults). To change these values, use the -APPStartAddr and
-APPLoadAddr option.
NOTE: Currently, YOU MUST USE THE UBL BINARY CREATED BY THE UBL PROJECT
IN THIS PACKAGE. If you use any other UBL binary, the boot procedure will most likely fail.

同样，slh 和 slt 也是一样的道理，只是他们是把代码下载到内部 RAM 或者 DDR2 上面去。
下面是使用介绍：

Serial Loader Usage
===================
More info can be found by running the utility with the '-h' option.
slh_DM36x.exe -h
1) Load a UBL or small UBL-like application to the DM36x IRAM
slh_DM36x.exe -load2IRAM <UBL binary file>
2) Load a larger image compiled to run at start of DDR space
slh_DM36x.exe -load2DDR <binary application file>
For the load to IRAM option, the file size is limited to 14KB, and the application assumes an entry
point address of 0x0100 (the smallest allowed). The entry point address canbe modified by using
the -startAddr command line option, with the address specified in hex.
For the load to DDR option, the file size is limited to 32MB, and the application assumes a load
address and entry point address of 0x80000000.
The entry point address can be altered by using the -startAddr command line option, as with the
-load2IRAM case. The load address can be altered from the default by using the -loadAddr
command line option

sfh_DM365x.exe 为 DVSDK 自带，所在位置如下图：

由于使用 sfh_DM36x.exe 需要安装.Net Framework 2.0 或更高的版本，所以先安装.net 固件。

三、烧写 UBL 和 UBOOT

1.PC 端打开命令行工具，把 sfh_DM36x.exe 和要烧写的 UBL， uboot 文件放在同一个目录下，
编写脚本 download.bat 然后使用命令
sfh_DM36x -nandflash ubl_DM36x_nand.bin u-boot.bin -p "COM1"
如果需要指定 UBOOT 的装在地址或入口地址的话需要加上 -APPStartAddr 和 -APPLoadAddr 指定。

PS: 如上图所示插上短路帽则将板子设为串口启动，BTSET[2:0]=011 即NAND Boot mode

烧写过程：
1、368 设备主板插上短路帽，超级终端连接设备，看到打印。

ps:此时 BTSET[2:0]=011 为串口模式

此时断开超级终端
2.烧写文件目录找到脚本，把里面的串口改为本地串口，运行该脚本，直到出现以下信息。

关闭该运行窗口，再次运行该脚本，打开运行窗口，出现以下信息

加载到 100%会自动关闭运行窗口
3.本地打开 tftp server 目录指向烧写文件目录
C:\Users\zslf\Desktop\shaoxie\sx\DM368\sx\u-boot 和 ubl 及烧写工具
4.打开虚拟机 ip 为 192.168.2.78(虚拟机要有文件系统)
5.关闭设备，拔掉短路帽，开启设备，会自动加载内核及文件系统，如下图
ps：此时 BTSET[2:0]=000 为 nand 启动模式

直到出现进入 uboot 界面如下图

6.在 uboot 下修改相关配置参数，依次设置以下指令，即完成板子烧写。

setenv bootargs dm365_imp.oper_mode=0 mem=48M console=ttyS0,115200n8 noinitrd rw
ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs video=davincifb:osd0=720x480x16,4050K ;setenv
bootcmd 'nand read 0x80700000 0x400000 0x400000;bootm 0x80700000';
saveenv
reset

四、烧写说明

DM368用于小型化设备作为视频监控设备，本文主要说明的是怎样烧写DM368.

DM368采用的是NandFlash作为存储芯片，采用的是ubi文件系统.
DM368烧写分为三个步骤：通过串口烧写UBL和U-boot；u-boot下烧写uImage，主机下烧写ubi文件系统，修改启动参数；制作SD卡；

烧写UBL和U-boot

1.将UBL、u-boot.bin和download.bat批处理程序放在一个文件夹下，如下图所示；

2.修改dwonload.bat中的串口设置

COM22修改为主机和板子相连的串口号(通过控制面板可以确认)；

3.设置板子为串口启动，并加电；

串口启动时用跳线帽短接指定的两个电阻;

4.串口烧写

分两次双击download.bat(必须执行两次双击，每次执行都必须执行完毕)。完成后即烧写完了UBL和U-boot,断电后取下两个跳线帽；
以下宏定义指令文件所在位置：
/home/zslf/dm368/dvsdk_dm368_4_02_00_06/psp/u-boot-2010.12/include/configs#
vi davinci_dm365evm.h
在编译uboot的时候设置 serverip、bootargs 等。

烧写内核和文件系统

第二部分烧写内核和文件系统实际上是自动化烧写完毕的。在这里分析下怎样实现的，主要是通过u-boot中bootcmd参数实现自动烧写uImage，nfs文件系统中软链接实现烧写ubi文件系统；

#define CONFIG_BOOTCOMMAND "tftp 0x80700000 uImage; nand erase 0x400000 0x400000; nand write 0x80700000 0x400000 0x400000;set bootcmd ' setenv bootcmd ' ';saveenv;nand read 0x80700000 0x400000 0x400000;bootm 0x80700000 ';set serverip 192.168.2.76;set ipaddr 192.168.2.194;saveenv;tftp 0x80700000 uImage;reset"

上述设置对应u-boot状态下bootcmd参数，含义是第一次上电后通过进入u-boot状态下通过tftp下载内核uIamge到内存0x80700000;修改再次启动的bootcmd参数；并将内核烧写到NandFlash中; ;修改再次启动的bootcmd参数;设置服务器ip(即主机IP)，板子的ip，再进行复位；
#define CONFIG_BOOTARGS \
"mem=60M console=ttyS0,115200n8 noinitrd rw eth=03:0E:EF:F2:FF:85 ip=192.168.2.194::192.168.2.1 nfsroot=192.168.2.78:/home/zslf/dm368/rootfs,nolock video=davincifb:osd0=720x480x16,4050K dm365_imp.oper_mode=0"
上述设置bootargs，实现nfs挂载，从而实现第一次进入nfs文件系统中后可以烧写ubi文件系统；
#define CONFIG_IPADDR 192.168.2.194
#define CONFIG_SERVERIP 192.168.2.76
#define CONFIG_GATEWAYIP 192.168.2.1
#define CONFIG_ETHADDR 0A:26:C4:9F:7D:19
设置服务ip,开发板地址，网关，mac地址；

在nfs文件系统的/etc/rc5.d/下有一个链接脚本，实现ubi文件系统的自动化烧写，如下图所示：

可以看出是一个软链接，真正的脚本在/zslf/write.sh
write.sh中的内容是：

rootfs-php为ubifs文件系统，需要放在nfs根根文件系统的zslf目录下；
上述脚本即为烧写ubi文件系统，烧写完毕后重启系统；

有上面的原理可以得出第二阶段的烧写步骤：
1.配置tftpd服务器，准备uImage内核,如下图所示：

例如：设置tftpd服务器的服务目录为D:\tftp32pd_base\DM368
将内核放在服务目录下，如下图所示：

2.配置虚拟机中nfs根文件系统和ubifs文件系统
主要是在/etc/export中设置，如下图所示

上述可知/home/zslf/dm368/rootfs为nfs根文件系统；ubi文件系统rootfs-php。

放在/home/zslf/dm368/rootfs/zslf/下
3.(取下短路帽，从Nand启动)，上电上电后，不要执行任何操作，系统自动烧写内核uImage和ubi文件系统，烧写完后，系统进行软复位，自动进入U-boot状态；
4.修改bootargs参数
修改bootargs参数，文件系统由nfs启动改为ubi文件系统启动；
修改如下：
setenv bootargs dm365_imp.oper_mode=0 mem=48M console=ttyS0,115200n8 noinitrd rw ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs video=davincifb:osd0=720x480x16,4050K ;setenv bootcmd 'nand read 0x80700000 0x400000 0x400000;bootm 0x80700000';
setenv bootcmd ‘nand read 0x80700000 0x400000 0x400000;bootm 0x80700000’
saveenv
reset;

五、制作SD卡

1.利用sd-format.sh脚本格式化sd卡，建立基本的SD卡；
2.拷贝/zslf文件系统；
至此DM368烧写完毕；

sd-format.sh 格式化脚本内容：

#!/bin/sh
e=""
m=""
n="xxxx"
while [ 1 ]
do
n="xxxx"
e=`fdisk -l | grep /dev/sdb1 | awk '{print $1}'`
if [ -z "$e" ];then
echo "####no sd ####"
else
echo "####have sd !####"
m=`df | grep media | awk '{print $1}'`
if [ -n "$m" ];then
umount $m
fi
#umount $e
echo "####start to format sd with ext3 filesystem!####"
mkfs.ext3 "$e"
echo "####end format sd!####"
#echo "copy zslf_app_dir"
mount $e /media/mmcblk0p1
#cp -a zslf /media/mmcblk0p1/
mkdir /media/mmcblk0p1/bak
mkdir /media/mmcblk0p1/video
umount $e
echo "##############zslf sd fomat and copy filesystem!
##########################"
echo "please remove sd!"
fi
sleep 5
if [ -n "$e" ];then
while [ -n "$n" ]
do
n=`fdisk -l | grep /dev/sdb1 | awk '{print $1}'`
sleep 5
done
fi
done

六、其他烧写方式

参看：DM368 jtag 烧写方法

参看：DM36x通过SD卡启动和烧写程序

七、启动信息

U-Boot 2010.12-rc2 (May 27 2014 - 16:50:48)

Cores: ARM 297 MHz
DDR:   243 MHz
DRAM:  128 MiB
NAND:  512 MiB
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
Net:   Ethernet PHY: LXT972 @ 0x01
DaVinci-EMAC
Hit any key to stop autoboot:  2  1  0 

NAND read: device 0 offset 0x400000, size 0x400000
 4194304 bytes read: OK
## Booting kernel from Legacy Image at 80700000 ...
   Image Name:   Linux-2.6.32.17-davinci1
   Created:      2015-11-23   9:14:53 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2243956 Bytes = 2.1 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux.................................................................................................................................................. done, booting the kernel.
Linux version 2.6.32.17-davinci1 (root@zslf-desktop) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #117 PREEMPT Mon Nov 23 17:14:48 CST 2015
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: DaVinci DM36x EVM
Memory policy: ECC disabled, Data cache writeback
DaVinci dm36x_rev1.2 variant 0x8
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 12192
Kernel command line: dm365_imp.oper_mode=0 mem=48M console=ttyS0,115200n8 noinitrd rw ubi.mtd=3 root=ubi0:rootfs rootfstype=ubifs video=davincifb:osd0=720x480x16,4050K
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 48MB = 48MB total
Memory: 43900KB available (4216K code, 393K data, 148K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:245
Calibrating delay loop... 147.86 BogoMIPS (lpj=739328)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
DaVinci: 8 gpio irqs
NET: Registered protocol family 16
davinci_serial_init:97: failed to get UART2 clock
EVM: HD imager video input
bio: create slab <bio-0> at 0
DM365 IPIPE initialized in Continuous mode
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pca9543a_probe
vpss vpss: dm365_vpss vpss probed
vpss vpss: dm365_vpss vpss probe success
dm365_afew_hw_init
lconfig->line_length is 0.
ch0 default output "COMPOSITE", mode "NTSC"
###### vpbe_encoder_init ######
###### vid_enc_register_encoder ######
###### mgr->num_encoders is 0 ######
###### **ch_id is 0 ######
###### mode_info.name is NTSC ######
###### vpbe_encoder_initialize ######
###### output is COMPOSITE,outindex is 0 ######
###### vpbe_encoder_setoutput ######
###### dm365 = 1 ######
###### mode_info->std is 1 ######
###### mode is NTSC ######
###### 22VPBE Encoder initialized ######
###### vpbe_encoder_setoutput ######
###### dm365 = 1 ######
###### mode_info->std is 1 ######
###### mode is NTSC ######
###### dm365 = 1 ######
###### mode_info->std is 1 ######
###### mode is NTSC ######
###### 33encoder->mode_ops->setmode: error is 0 ######
###### davinci_enc_set_mode_platform : next davinci_enc_priv_setmode ######
VPBE Encoder Initialized
###### 11VPBE Encoder Initialized ######
Switching to clocksource timer0_1
musb_hdrc: version 6.0, cppi-dma, host, debug=0
musb_hdrc: USB Host mode controller at fec64000 using DMA, IRQ 12
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: MUSB HDRC host driver
usb usb1: Manufacturer: Linux 2.6.32.17-davinci1 musb-hcd
usb usb1: SerialNumber: musb_hdrc
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Installing knfsd (copyright (C) 1996 [email protected]).
msgmni has been set to 85
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
###### davinci_enc_get_mode ######
###### davinci_get_cur_encoder ######
###### davinci_enc_get_mode ######
###### davinci_get_cur_encoder ######
###### davinci_enc_get_mode ######
###### davinci_get_cur_encoder ######
davincifb davincifb.0: dm_osd0_fb: 720x480x16@0,0 with framebuffer size 4050KB
davincifb davincifb.0: dm_vid0_fb: 0x0x16@0,0 with framebuffer size 1020KB
###### davinci_enc_get_mode ######
###### davinci_get_cur_encoder ######
###### davinci_enc_get_mode ######
###### davinci_get_cur_encoder ######
davincifb davincifb.0: dm_osd1_fb: 720x480x4@0,0 with framebuffer size 675KB
davincifb davincifb.0: dm_vid1_fb: 0x0x16@0,0 with framebuffer size 1020KB
DM365 IPIPEIF probed
imp serializer initialized
davinci_previewer initialized
davinci_resizer initialized
davinci gpio led module init ....... 
register davinci gpio module is ok ....... 
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0x1d06000 (irq = 41) is a 16550A
brd: module loaded
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit)
nand_bbt: ECC error while reading bad block table
Creating 5 MTD partitions on "davinci_nand.0":
0x000000000000-0x0000003c0000 : "bootloader"
0x0000003c0000-0x000000400000 : "params"
0x000000400000-0x000000820000 : "kernel"
0x000000820000-0x000008820000 : "filesystem"
0x000008820000-0x000020000000 : "zslf"
davinci_nand davinci_nand.0: controller rev. 2.3
UBI: attaching mtd3 to ubi0
UBI: physical eraseblock size:   131072 bytes (128 KiB)
UBI: logical eraseblock size:    126976 bytes
UBI: smallest flash I/O unit:    2048
UBI: VID header offset:          2048 (aligned 2048)
UBI: data offset:                4096
usb 1-1: new high speed USB device using musb_hdrc and address 2
usb 1-1: New USB device found, idVendor=12d1, idProduct=15c1
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: HUAWEI Mobile V7R11
usb 1-1: Manufacturer: Huawei Technologies Co., Ltd.
usb 1-1: SerialNumber: 0123456789ABCDEF
usb 1-1: configuration #2 chosen from 3 choices
UBI: attached mtd3 to ubi0
UBI: MTD device name:            "filesystem"
UBI: MTD device size:            128 MiB
UBI: number of good PEBs:        1024
UBI: number of bad PEBs:         0
UBI: max. allowed volumes:       128
UBI: wear-leveling threshold:    4096
UBI: number of internal volumes: 1
UBI: number of user volumes:     1
UBI: available PEBs:             5
UBI: total number of reserved PEBs: 1019
UBI: number of PEBs reserved for bad PEB handling: 10
UBI: max/mean erase counter: 2/1
UBI: image sequence number: 0
UBI: background thread "ubi_bgt0d" started, PID 354
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>

 cdc_bind,[546]
usb0: register 'cdc_ether' at usb-musb_hdrc-1, CDC Ethernet Device, 02:1e:10:1f:00:00
usbcore: registered new interface driver cdc_ether
console [netcon0] enabled
netconsole: network logging started
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
option 1-1:2.2: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
option 1-1:2.3: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
option 1-1:2.4: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2
option 1-1:2.5: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3
option 1-1:2.6: GSM modem (1-port) converter detected
usb 1-1: GSM modem (1-port) converter now attached to ttyUSB4
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
usbcore: registered new interface driver usbtest
rtc-ds1307 1-0068: rtc core: registered ds1339 as rtc0
i2c /dev entries driver
Linux video capture interface: v2.00
ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter)
ths7303 1-002c: ths7303 write failed
ths7303: probe of 1-002c failed with error -121
vpfe_init
vpfe-capture: vpss clock vpss_master enabled
vpfe-capture vpfe-capture: v4l2 device registered
vpfe-capture vpfe-capture: video device registered
EVM: switch to tvp5150 SD video input
tvp5150 1-005d: chip found @ 0x5d (DaVinci I2C adapter)
vpfe-capture vpfe-capture: v4l2 sub device tvp5150 registered
EVM: switch to tvp7002 HD video input
vpfe-capture vpfe-capture: v4l2 sub device ths7353 register fails
vpfe_register_ccdc_device: DM365 ISIF
DM365 ISIF is registered with vpfe.
af major#: 250, minor# 0
AF Driver initialized
aew major#: 249, minor# 0
AEW Driver initialized
###### osd_init ######
### VPBE OSD DRIVER INIT ###
Trying to register davinci display video device.
layer=c10b1400,layer->video_dev=c10b1570
Trying to register davinci display video device.
layer=c10b1800,layer->video_dev=c10b1970
davinci_init:DaVinci V4L2 Display Driver V1.0 loaded
watchdog watchdog: heartbeat 60 sec
davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode
Advanced Linux Sound Architecture Driver Version 1.0.21.
No device for DAI tlv320aic3x
No device for DAI davinci-i2s
asoc: tlv320aic3x <-> davinci-i2s mapping ok
ALSA device list:
  #0: DaVinci EVM (tlv320aic3x)
TCP cubic registered
NET: Registered protocol family 17
Clocks: disable unused mmcsd1
Clocks: disable unused spi0
Clocks: disable unused spi1
Clocks: disable unused spi2
Clocks: disable unused spi3
Clocks: disable unused spi4
Clocks: disable unused pwm0
Clocks: disable unused pwm1
Clocks: disable unused pwm2
Clocks: disable unused pwm3
Clocks: disable unused timer1
Clocks: disable unused timer3
Clocks: disable unused emac
Clocks: disable unused voice_codec
Clocks: disable unused rto
Clocks: disable unused mjcp
davinci_emac_probe: using random MAC addr: b2:55:85:e9:2b:0e
emac-mii: probed
mmc0: new high speed SDHC card at address e624
rtc-ds1307 1-0068: setting system clock to 2015-11-24 11:00:54 UTC (1448362854)
mmcblk0: mmc0:e624 SU64G 59.4 GiB 
 mmcblk0: p1
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size:   126341120 bytes (123380 KiB, 120 MiB, 995 LEBs)
UBIFS: journal size:       6348800 bytes (6200 KiB, 6 MiB, 50 LEBs)
UBIFS: media format:       w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root:  4952683 bytes (4836 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:14.
Freeing init memory: 148K

INIT: version 2.86 booting
Please wait: booting...
Error Cannot open /dev/tty0: No such device or address
Starting udev
udev: starting version 141
Root filesystem already rw, not remounting
Caching udev devnodes
Populating dev cacheFAT: bogus number of reserved sectors
VFS: Can't find a valid FAT filesystem on dev mmcblk0.
mv: cannot rename '/tmp/devices': No such file or directory
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
kjournald starting.  Commit interval 5 seconds
EXT3 FS on mmcblk0p1, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
ALSA: Restoring mixer settings...
Configuring network interfaces... eth0: attached PHY driver [LXT971] (mii_bus:phy_addr=1:01, id=1378e2)
done.
Setting up IP spoofing protection: rp_filter.

INIT: Entering runlevel: 5
Starting system message bus: dbus.
Starting telnet daemon.
Starting syslogd/klogd: done
CMEMK module: built on Oct 26 2015 at 22:19:29
  Reference Linux version 2.6.32
  File /home/zslf/dm368/dvsdk_dm368_4_02_00_06/linuxutils_2_26_01_02_bak/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c
allocated heap buffer 0xc7000000 of size 0x4400000
heap fallback enabled - will try heap if pool buffer is not available
CMEM Range Overlaps Kernel Physical - allowing overlap
CMEM phys_start (0x1000) overlaps kernel (0x80000000 -> 0x83000000)
cmemk initialized
IRQK module: built on Oct 26 2015 at 22:17:36
  Reference Linux version 2.6.32
  File /home/zslf/dm368/dvsdk_dm368_4_02_00_06/linuxutils_2_26_01_02_bak/packages/ti/sdo/linuxutils/irq/src/module/irqk.c
irqk initialized
EDMAK module: built on Oct 26 2015 at 22:16:49
  Reference Linux version 2.6.32
  File /home/zslf/dm368/dvsdk_dm368_4_02_00_06/linuxutils_2_26_01_02_bak/packages/ti/sdo/linuxutils/edma/src/module/edmak.c
/zslf/appZSLF.sh: line 9: ppp_config_copy: not found
start copy th config file from zslf/config to /etc/ppp/peers.
cp: cannot stat '/zslf/config/ppp-off': No such file or directory
cp: cannot stat '/zslf/config/ppp0_on_state.txt': No such file or directory
############## ZSLF  ##################
start copy the config file from zslf to thttpd/www.
/zslf/appZSLF.sh: line 17: ppp_config_copy: not found
Create a shared memory segment 32769.
24 Nov 11:01:09 ntpdate[993]: no servers can be used, exiting
mkdir: cannot create directory '/media/mmcblk0p1/bak': File exists
## davinci_pio_led:ioctl:out: GPIO-81=1 now.ret= 0 ## 
setrlimit ok
FD_SETSIZE= 1024
### Serial_ttyUSB0_Init ###
### Complete serial_open ###
### Complete serial_config ###
### Complete fcntl ###
### Serial_ttyUSB0_Init End ###
###  MU909_SetCFUN ###
start MU909_SetCFUN 
##strATCommand is AT+CFUN=1
.
AT+CFUN=1


OK


##strATCommand is AT+CMEE=2
.
AT+CMEE=2


OK


##strATCommand is AT+CPIN?
.
AT+CPIN?


+CPIN: READY



OK


##strATCommand is AT+CEREG=2
.
AT+CEREG=2


OK


##strATCommand is AT^HCSQ?
.
AT^HCSQ?


^HCSQ: "LTE",52,49,166,34



OK


##strATCommand is AT+COPS?
.
AT+COPS?


+COPS: 0,0,"CMCC",7



OK


##strATCommand is AT^SYSCFGEX="03",3fffffff,1,2,7fffffffffffffff,,
.
AT^SYSCFGEX="03",3fffffff,1,2,7fffffffffffffff,,


OK


##strATCommand is AT^NDISDUP=1,1,"cmnet"
.
AT^NDISDUP=1,1,"cmnet"


OK



^NDISSTAT: 1,,,"IPV4"



^NDISSTAT: 1,,,"IPV6"


udhcpc (v1.13.2) started
Sending discover...
Sending select for 10.67.239.228...
Lease of 10.67.239.228 obtained, lease time 518400
adding dns 221.130.33.60
adding dns 221.130.33.52
######## encode #########
### timenow->tm_year = 115 ###

 _____                    _____           _         _   
|  _  |___ ___ ___ ___   |  _  |___ ___  |_|___ ___| |_ 
|     |  _| .'| . | . |  |   __|  _| . | | | -_|  _|  _|
|__|__|_| |__,|_  |___|  |__|  |_| |___|_| |___|___|_|  
              |___|                    |___|            

Arago Project http://arago-project.org dm368-evm ttyS0

Arago 2011.02 dm368-evm ttyS0

dm368-evm login: 24 Nov 11:01:32 ntpdate[1189]: no server suitable for synchronization found
zslf module ok...
dlsym load ok!
***after***
#### parseStreamingArgs - streaming to [124.65.158.106:22616] ####
#### parseStreamingArgs - streaming to [192.168.2.91:22616] ####
#### parseVideoArgs - (0) 720x480 ####
#### parseVideoArgs - (1) 720x480 ####
#### parseAudioArgs - 44100,2,32000,1 ####
### parseArgs - config/devInfo.txt, Name:[联通小单?##### output_store ######
?56001],ID:[YS-###### davinci_get_cur_encoder ######
56001] ###
Encode streaming star###### vpbe_encoder_initialize ######
ting...
1
2
3
4
###### output is COMPOSITE,outindex is 0 ######
###### vpbe_encoder_setoutput ######
###### dm365 = 1 ######
###### mode_info->std is 1 ######
###### mode is NTSC ######
###### 22VPBE Encoder initialized ######
###### vpbe_encoder_setoutput ######
###### dm365 = 1 ######
###### mode_info->std is 1 ######
###### mode is NTSC ######
###### davinci_enc_set_output : next davinci_enc_set_mode_platform ######
###### davinci_enc_set_mode_platform : next davinci_enc_priv_setmode ######
###### output_show ######
###### davinci_enc_get_output ######
###### davinci_get_cur_encoder ######
###### mode_store ######
###### davinci_enc_get_mode ######
###### davinci_get_cur_encoder ######
###### davinci_enc_set_mode ######
###### davinci_get_cur_encoder ######
###### dm365 = 1 ######
###### mode_info->std is 1 ######
###### mode is PAL ######
###### davinci_enc_set_mode : next davinci_enc_set_mode ######
###### davinci_enc_set_mode_platform : next davinci_enc_priv_setmode ######
###### mode_show ######
###### davinci_enc_get_mode ######
###### davinci_get_cur_encoder ######
Found width=720 height=480, yres_virtual=480,xres_virtual=720, l###### davinci_enc_get_mode ######
###### davinci_get_cur_encoder ######
###### davinci_enc_get_mode ######
###### davinci_get_cur_encoder ######
###### davinci_enc_set_mode ######
###### davinci_get_cur_encoder ######
###### dm365 = 1 ######
###### mode_info->std is 1 ######
###### mode is PAL ######
###### davinci_enc_set_mode : next davinci_enc_set_mode ######
###### davinci_enc_set_mode_platform : next davinci_enc_priv_setmode ######
###### davinci_enc_get_mode ######
###### davinci_get_cur_encoder ######
ine_length=384
###### davinci_enc_get_mode ######
###### davinci_get_cur_encoder ######
###### davinci_enc_get_mode ######
###### davinci_get_cur_encoder ######
5
6
7
sd write module ok...
____Mp4Recover module ok!
/media/mmcblk0p1/video/temp/YS-56001_11-24_10h59m49s.mp4 Need to recover!
~~~~~~~~~~~~~~now! is ready to recover!
now! is get_data!
get data all!
now! is make mp4!
### sps.pic_width_in_mbs_minus1 : 0
    sps.pic_height_in_map_units_minus1 : 0
    sps.vui_parameters.time_scale : 139596691
    sps.vui_parameters.num_units_in_tick : 376021250 ###
now! is follow handle!
__cgy in main all!
sd write init ok## davinci_pio_led:ioctl:out: GPIO-47=0 now.ret= 0 ## 

func_sd_input_data ok
+
###READY TO PM###18
there is a sd need to be mounted 0000
### name:[mpeg4enc] ###
### name:[h264enc] ###
#davinci_resizer davinci_resizer.2: RSZ_G_CONFIG:0:1:124
## name:[mpeg2enc] ###
### name:[jpegenc] ###
### name:[g711enc] ###
### name:[aacenc] ###
###Ready to open encoder###
davinci_previewer davinci_previewer.2: ipipe_set_preview_config
############
v4l2_device_call_until_err sdinfo->grp_id : 5.
vpfe-capture vpfe-capture: error in getting g_fmt from sub device
############
v4l2_device_call_until_err sdinfo->grp_id : 5.
###succeed to open encoder###
setrlimit ok
FD_SETSIZE= 1024
udp port multiplexing : 1
#### InitUdpSocket - SO_RCVBUF : 217088, SO_SNDBUF : 217088 ####
mount: /dev/mmcblk0p1 already mounted or /media/mmcblk0p1/ busy
###### len = 26 #########
mount: according to mtab, /dev/mmcblk0p1 is already mounted on /media/mmcblk0p1
add sd card
############# PUID:83
bjwLgn.strModel:bjw-2013
PUID=83
### do_login: sockfd = 32 
Login response status : d
 ACK 
vpfe-capture vpfe-capture: IPIPE Chained
vpfe-capture vpfe-capture: Resizer present
*****input=0****EVM: switch to tvp5150 SD video input
***
############
v4l2_device_call_until_err sdinfo->grp_id : 5.
###j=1###
***  Video ASK Rep  *** 
startdata ok!
*****queryInput=0*******
############
v4l2_device_call_until_err sdinfo->grp_id : 5.
setsockopt ok!
vpfe-capture vpfe-capture: width = 736, height = 480, bpp = 1
vpfe-capture vpfe-capture: adjusted width = 736, height = 480, bpp = 1, bytesperline = 736, sizeimage = 529920
vpfe-capture vpfe-capture: width = 736, height = 480, bpp = 1
vpfe-capture vpfe-capture: adjusted width = 736, height = 480, bpp = 1, bytesperline = 736, sizeimage = 529920
### BJW_DealMsg - VIDEO: FORCE IDR ###
BJW_DealMsg - CONNECTED 42
### videoThrFxn - video0 construct IDR ###
***succeed to get capture***
### sps.pic_width_in_mbs_minus1 : 0
    sps.pic_height_in_map_units_minus1 : 0
    sps.vui_parameters.time_scale : 139596691
    sps.vui_parameters.num_units_in_tick : 376021250 ###
.
dm368-evm login: 
 _____                    _____           _         _   
|  _  |___ ___ ___ ___   |  _  |___ ___  |_|___ ___| |_ 
|     |  _| .'| . | . |  |   __|  _| . | | | -_|  _|  _|
|__|__|_| |__,|_  |___|  |__|  |_| |___|_| |___|___|_|  
              |___|                    |___|            

Arago Project http://arago-project.org dm368-evm ttyS0

Arago 2011.02 dm368-evm ttyS0

dm368-evm login: root

root@dm368-evm:~#

本文链接：https://blog.csdn.net/qq_29350001/article/details/73499079

原作者删帖不实内容删帖广告或垃圾文章投诉

智能推荐

wget报错-程序员宅基地

文章浏览阅读4.5k次，点赞5次，收藏6次。1.刚开始我输入的指令是这样的wget https://pjreddie.com/media/files/yolov3-tiny.weights2.发现报错 ERROR: cannot verify pjreddie.com's certificate, issued by `/C=US/O=Let's Encrypt/CN=Let's Encrypt Authority X3':..._wget报错

Java 转换utf8,java：如何将文件转换为utf8-程序员宅基地

文章浏览阅读755次。i have a file that have some non-utf8 caracters (like "ISO-8859-1"), and so i want to convert that file (or read) to UTF8 encoding, how i can do it?The code it's like this:File file = new File("some_f..._new file怎么转化utf8

Vue中引入字体并解决字体文件过大问题_vue 引入字体包体积过大-程序员宅基地

文章浏览阅读5.6k次。利用 CSS3 @font-face 规则指定名为"myFirstFont"的字体，并指定在哪里可以找到它的URL：@font-face{font-family: myFirstFont;src: url('Sansation_Light.ttf'), url('Sansation_Light.eot'); /* IE9 */}在main.js中全局引用文件import '@/styles/index.scss'解决字体文件过大问题Fontmin - 字体子集化方案_vue 引入字体包体积过大

转-- 定制PYNQ的overlay-程序员宅基地

文章浏览阅读551次。一、用HLS生成一个定制IP（加速器）（1）首先打开vivado hls，本人的版本是2017.2，点击创建一个新工程。（2）设置工程名和路径，顶层函数设置为add，创建一个新的C++程序，名字叫做adder.cpp,不用在testbench中添加文件。选择板子的时候搜索xc7z020clg400-1，这是PYNQ的板子号，选择完成。（3）在左侧的..._定制pynq的overlay

rocketMQ中，消费者、消费者组、Topic、队列的关系_rocketmq topic和queue关系-程序员宅基地

文章浏览阅读2w次，点赞28次，收藏76次。初学roketMQ的同学可能会比较难以理解这四者之间的关系，这里我来理一下。1、消费者和消费者属于个体与群体的关系，非常容易理解，不赘述2、Topic是相当于一种消息类型，而队列queue则是属于某个Topic下的更细分的一种单元。举个例子。Topic代表老虎，是一种动物类型，而队列就相当于东北虎，是对老虎的更详细描述。3、在同一个消费者组下的消费者，不能同时消费同一个queue。4、一个消费者组下的消费者，可以同时消费同一个Topic下的不同队列的消息。5、不同消费者组下的消费者，可以同时._rocketmq topic和queue关系

mysql truncate某列_MySQL之删_delete-truncate-程序员宅基地

文章浏览阅读229次。MySQL增删改查之删_delete-truncate一、DELETE语句删除数据记录1、在单表中删除行语法：DELETE [IGNORE] FROM tbl_name[WHERE where_condition][ORDER BY ...][LIMIT row_count]①从表中删除满足WHERE条件的所有行；②没有WHERE条件，则删除表中的所有行基本格式：delete from wh..._mysql truncate 某行数据